Design Book › Sizing a joint

Sizing a joint

Size every joint on continuous torque, at the real voltage, at the real temperature. In continuous operation, keep motor torque below the thermally set limit, not the peak or stall value [1]. A servo's stall torque is its maximum momentary output and differs from its continuous rating [2]. Most motors fail from overload held over time: a torque that stays high for longer than the motor can carry it [3].

For each joint, a designer must produce four numbers: RMS torque over the duty cycle, peak torque with its duration, top speed at the minimum bus voltage, and steady winding temperature in the real mount.

Peak is not continuous

Catalogs print several torques. They are different limits.

Peak is not continuous
TermWhat it meansSource
Rated, nominal or continuousThermally set limit for steady work[1]
PeakIntermittent limit. One source lists 20 s and 2 s peaks separately, and notes a peak given with no duration.[4], [5]
StallA servo's maximum momentary output. Should usually exceed the load peak torque.[2], [6]
Repeated peak, momentary peak (strain wave)Gear limits, not motor limits. See chapter 6.[7], [8]

The gap between them varies by part. Do not use a fixed multiplier. The motor row comes from the TQ data sheet. The actuator rows come from the open Dynamic Robot Joint Actuator Comparison data set, which collects maker specs.

Peak is not continuous
PartRated or continuousPeak or stallPeak over ratedKind
ROKAE HSA-17, strain wave51 Nm70 Nm start-stop peak1.4spec
MyActuator EPS-CEM-25, cycloidal15 Nm25 Nm1.7spec
DAMIAO DM-J4310-2EC V1.1, QDD3 Nm7 Nm2.3spec
Leadshine HRV2-90FXD19 31:1, cycloidal50 Nm120 Nm2.4spec
TQ ILM85x26, frameless motor, 48 V2.9 Nm9.37 Nm3.2spec
ASTRALL AT 7510, planetary50 Nm300 Nm6.0spec
Joy-Motion JRM-45-100, strain wave3.95 Nm44.8 Nm11.3spec

The two strain-wave actuators give 1.4 and 11.3, so the family does not set the ratio either.

Write the duration next to a peak value. Urs et al. list 20 s peak, 2 s peak and continuous torque separately, and note that the Mini Cheetah peak duration was not provided [5]. Record the supply voltage next to every torque and speed value. The 7.4 V STS3215 is rated at 16.5 kg.cm stall at 6 V, and the 12 V version at 30 kg.cm [9]. The database also holds a second stall value at 6 V for the 7.4 V part, from another source. This site does not show it. Match the exact revision. CubeMars lists AK10-9 V2.0 at 48 Nm peak and V3.0 KV60 at 53 Nm [10].

Method

Work these steps for each joint, in order. Use the joint with the worst duty first.

  1. Find the load at the joint. Use tau = J^T F at every reachable pose and payload [11]. Add gravity and dynamics with tau = M ddq + c + g [12]. Add wire harness flex [13].
  2. Count the rotor. Reflected inertia is G^2 * J_rotor [14]. It can be on the order of link inertia, or larger [15]. Put it in the dynamics and repeat step 1 [16].
  3. Write the duty cycle. List each segment as a time and a torque, with the rest time included. Compute M_RMS = sqrt(sum(t_i * M_i^2) / t_total) [17].
  4. Reflect to the motor. n_mot = i * n_L and M_mot = M_L / (i * eta) [18]. Gear output is tau_output = eta * G * tau_motor, with eta at or below 1 [19]. Check the gearbox's own limits in chapter 6.
  5. Check continuous torque. Require M_N > M_RMS [20]. For continuous operation at one load point, M_N > M_L [21]. Allow for no-load current: M_N = k_M * (I_N - I_0) [22].
  6. Check peak torque. The motor's stall torque should usually exceed the load peak torque: M_H > M_max [6]. Limit peak current: I_on <= I_N * sqrt(T / t_on), with t_on no longer than the winding time constant [23]. Expect overload times from several seconds on the smallest motors to about one minute on the largest [24].
  7. Check speed and voltage. Start from the voltage at the motor: U_motor = U_supply - U_drop_amp - cable drop [25]. Use minimum bus voltage after sag [26]. Keep every operating point under the speed-torque line, w <= V/k_t - (R/k_t^2) * tau [27], [28]. Keep a regulating reserve of about 20 percent [29]. Stay under the catalog limit speed [30].
  8. Check the drive and supply. The amplifier must deliver both average and peak current [31]. Battery and amplifier limits can set the peak [32], [33].
  9. Check heat. T_w = T_amb + (Rth1 + Rth2) * R * I_rms^2 <= T_max [34]. Use hot resistance: R_T = R25 * (1 + 0.0039 * (T - 25)) [35]. Close the loop with the feedback form [36]. Re-derive for your ambient and mount [37], [38], and add speed-dependent loss [39].
  10. Compute the margin. NASA's form for spaceflight mechanisms is TM = T_avail / (sum(FSf*Tf) + sum(FSv*Tv) + sum(FSa*Ta)) - 1 >= 0 [40]. Minimum available motor torque is typically understood to include magnetic losses, mechanical losses and ripple [41]. Take the margin on both sides of the gearbox [42], over the full range of motion [43].
  11. Measure. Motor data from a catalog are averages [44]. NASA-STD-5017B has EC brushless motor constants measured, or calculated from measured values, with flight-representative drive electronics for the torque-speed curve [45]. Measure constants with your own drive. Run the duty test until the temperature slope falls under 0.1 C per minute, or for five thermal time constants [46].

Worked check A: a small actuator from its data sheet

The part is DM-J4310-2EC V1.1 at 24 V. The open actuator data set lists it at 3 Nm rated and 7 Nm peak at the output, with 120 rpm rated speed and 200 rpm maximum speed. The load in this example is a design assumption, not a test: 1.5 kg on a 30 cm lever, held for 10 minutes. Take the lever horizontal, the worst case.

  1. Load: 1.5 kg x 9.81 m/s^2 x 0.30 m is 4.41 Nm.
  2. Continuous check: the data set lists 3 Nm rated. As a continuous load, 4.41 Nm fails the continuous-torque limit [1], although it is well under the 7 Nm peak. Work above the continuous limit is intermittent only [4].
  3. Duty limit: with rest at zero torque, M_RMS = M * sqrt(t_on / T). Requiring the rated 3 Nm or less gives t_on / T of at most (3 / 4.41)^2, which is 0.46 [17].
  4. Cross-check with the square-root law: the rated 3 Nm gives 3 x 1.414, or 4.24 Nm, at 50 percent duty and 4.24 x 1.414, or 6 Nm, at 25 percent [47]. The 4.41 Nm load falls between them, which agrees with the duty limit above.
  5. Speed: take the 200 rpm maximum speed as the no-load point, and the 120 rpm rated speed at 3 Nm as a second point on the speed-torque line [27]. The slope is (200 - 120) / 3, or 26.7 rpm per Nm. At 4.41 Nm the line gives 200 - 26.7 x 4.41, about 82 rpm. The line meets zero speed at 200 / 26.7, or 7.5 Nm, close to the listed 7 Nm peak, so the two points agree. Treat the result as an estimate at 24 V.
  6. Heat: the database holds no thermal resistance for this actuator, so the heat step of the method cannot run. A 10-minute hold proves no steady state. Run the duty test until the temperature slope falls under 0.1 C per minute, or for five thermal time constants [46]. Do not count on protection in the drive until you have checked it. In a Robonine test of the STS3215 servo, issues appeared at 71 C with no sign of thermal protection, and a later page comment says firmware cuts torque near 70 C [48]. Add a host-side temperature limit.

Result: design this actuator to 3 Nm continuous. Allow 4.41 Nm only in a measured duty cycle of at most 46 percent on time, with temperature logged.

Worked check B: a frameless motor in your own housing

The part is TQ ILM85x26, a frameless motor at 48 V. Its data sheet lists 11.5 A rated current, 0.32 ohm terminal resistance at 20 C, 253 mNm/A, 2.9 Nm rated torque and 9.37 Nm peak torque. A frameless motor has no housing of its own, so the data sheet gives no thermal resistance: TQ notes that thermal behaviour depends on the installation. The question turns round: what heat path must your housing give? Take 20 C ambient, the temperature of the resistance value. The database lists no winding limit for this motor, so take 125 C, a value often used as the maximum for stator windings [49].

  1. Copper loss when cold at rated current, from the data sheet values: 0.32 x 11.5 x 11.5 is 42.3 W [34]. This treats the terminal resistance as one winding, as the method does.
  2. Allowed rise: 125 - 20 is 105 K.
  3. With resistance feedback, the rise computed from cold loss must stay under 105 / (1 + 0.0039 x 105), which is 74.5 K [36].
  4. Thermal resistance from winding to ambient: 74.5 K / 42.3 W is 1.76 K/W at most [34]. Your housing must reach this to carry the rated current all the time.
  5. Suppose your housing reaches only 3 K/W. That is a design assumption for this example. Hot resistance at 125 C is 0.32 x (1 + 0.0039 x 105), or 0.451 ohm [35]. The guideline states the coefficient from 25 C, and this example applies it from the 20 C value on the data sheet. That changes the result by well under 1 percent. The copper-only current limit is sqrt(105 / (3 x 0.451)), which is 8.81 A. That gives 0.253 x 8.81, or 2.23 Nm, about 77 percent of the rated torque.
  6. Copper loss is not the whole budget [39]. Friction and eddy losses grow with speed. The data sheet gives no no-load current to estimate them, so treat both limits above as upper bounds at low speed.
  7. Nominal torque: k_t * I_N gives 0.253 x 11.5, or 2.91 Nm, against the data sheet 2.9 Nm. The form k_M * (I_N - I_0) also subtracts the no-load current [22], which the data sheet does not give. Use the lower number in a margin.
  8. Mount: a housed motor states its thermal values for one test mount. maxon gives its values for a motor on a vertical plastic plate [50]. A metal flange on a good holder can lower Rth2, the housing-to-ambient part, by up to 80 percent [51]. Measure your own housing before you claim a value [38].

Also note that TQ states the 9.37 Nm peak at 20 percent deviation from linearity. Near that current, tau = k_t * I [52] gives more torque than this part delivers. Use the listed peak value.

Torque margin factors

These minimum factors are from a NASA mechanisms standard, Table 1. They are written for spaceflight mechanisms [40]. Using the form on another critical joint is this book's choice, not the standard's. Better evidence earns smaller factors.

Torque margin factors
How the torque was foundVariableFixedAccelerationSource
Theory or analysis3.001.501.25[53]
Development or qualification test, as the guideline lists2.501.351.15[54]
Acceptance test of flight hardware at environmental extremes2.001.251.10[55]

Combine only worst cases that can occur together [56]. Keep holding torque margin above zero by the same equation and table, at specified positions in the full range of motion [57]. Do not apply this NASA margin to a mechanism that must provide a specific torque within a narrow tolerance range [58].

Thermal limits

Thermal limits
LimitValueScopeSource
Rotor, graphite brush and EC motors125 Cmaxon; individual cases up to 155 C[59]
Rotor, precious metal brush motors85 Cmaxon[60]
Open motor winding test125 C, steadyStanford Doggo; a value often used as the maximum for stator windings[49]
Any excursionDo not exceed the limit, even brieflymaxon[61]
Copper resistance0.0039 per K from 25 C; nearly 20 percent higher at 75 Cmaxon[35], [62]
Magnet weakening1 to 10 percent at 75 Cmaxon, by material[63]
Power MOSFET junction125 C, or 40 C below maximum, whichever is lowerNASA flight parts; stricter than commercial[64]
IC junction110 C, or 40 C below maximum, whichever is lowerNASA flight parts[65]
Continuous touch surface44 CNASA crewed spacecraft; closest public figure found[66]
Surface warningLabels from 45 to 50 C; protection above 50 CNASA crewed spacecraft[67]
Temperature test margin10 C beyond expected rangeGSFC flight mechanisms[68]

Model winding and stator as separate stages. The winding heats in seconds and the stator in 1 to 30 minutes [69]. That is why a short peak survives and a long one does not.

Outrunner motors trade heat dissipation and inertia for torque density [70]. Measure thermal resistance on the motor you choose.

Choosing the ratio

Ratio is a trade, not a free gain. A higher ratio adds static torque, but reflected inertia grows with ratio squared and friction rises [71]. A lower ratio reduces reflected inertia and can raise Joule heat [72]. For maximum acceleration, Slocum sets the ratio so the power to accelerate the motor equals the power to accelerate the load. That assumes a triangular velocity profile and low friction and external forces [73]. These aims differ. Sweep the ratio in simulation for your duty cycle.

Current maps to torque only at low ratio. Above about 10 you cannot ignore backlash, vibration and friction [74]. Quasi-direct drive uses a single-stage reduction with a ratio under 10:1 [75], [76].

Sources

Each guideline in this chapter with its source, the date it was read and the exact words of the source. Level: must means breaking it causes failure or harm, should is good practice, guide is a rule of thumb.

  1. In continuous operation keep motor torque below the thermally set continuous limit, not the peak or stall value. Level: must. hades.mech.northwestern.edu 2026-11-08
  2. A servo's stall torque is its maximum momentary output and differs from its continuous rating. Real-world output is generally closer to the performance-graph measurements. Level: guide. emanual.robotis.com 2026-11-08
  3. Remember that the primary cause of motor failure is too much torque for too long. Level: must. pergatory.mit.edu 2026-11-08
  4. Treat operation above the continuous region as intermittent only; extended operation there risks overheating. Level: must. hades.mech.northwestern.edu 2026-11-08
  5. Urs et al. (3D-printed actuators) list 20 s peak, 2 s peak and continuous torque separately and note the Mini Cheetah peak duration was not provided. Level: guide. arxiv.org 2026-11-08
  6. The selected motor's stall torque should usually exceed the load peak torque. Level: should. maxonmotor.com 2026-11-08
  7. Keep acceleration and deceleration torque below repeated peak torque. Level: must. harmonicdrive.net 2026-11-08
  8. Do not let momentary peak torque occur during normal operating cycles; allow it only in a collision or an emergency stop. Level: must. harmonicdrive.net 2026-11-08
  9. The STS3215 7.4 V version is rated at 16.5 kg·cm stall torque at 6 V; the 12 V version is rated at 30 kg·cm. Level: guide. github.com 2026-11-08“The 12V version has a stall torque of 30kg.cm.”
  10. CubeMars lists the AK10-9 V2.0 at 48 Nm peak and the AK10-9 V3.0 KV60 at 53 Nm peak. Level: guide. cubemars.com 2026-11-08
  11. Find joint torques from wrench with tau = J^T F, using the same frame for J and F. Level: should. hades.mech.northwestern.edu 2026-11-08
  12. Include gravity in the joint torque budget from the equations of motion, tau = M ddq + c + g. Level: should. hades.mech.northwestern.edu 2026-11-08
  13. Include wire harness flex forces and long-term set as a resisting torque. Level: should. standards.nasa.gov 2026-11-08“Wire harness loads (flex forces and long-term set)”
  14. Compute the rotor's reflected inertia at the joint as G squared times rotor inertia. Level: guide. hades.mech.northwestern.edu 2026-11-08
  15. Reflected rotor inertia can be on the order of, or larger than, the link inertia. Level: guide. hades.mech.northwestern.edu 2026-11-08
  16. Include rotor apparent inertia in the inverse dynamics when it is non-negligible relative to the link inertia. Level: must. hades.mech.northwestern.edu 2026-11-08
  17. Compute cycle RMS torque as the square root of the sum of time times torque squared, divided by total cycle time including rest. Level: guide. maxonmotor.com 2026-11-08
  18. Before motor selection, convert load speed with the reduction ratio and load torque with ratio and gear efficiency to the motor shaft. Level: should. maxonmotor.com 2026-11-08
  19. Multiply gear output torque by efficiency: tau_gear = eta G tau_motor, with eta at or below 1. 1 Level: should. hades.mech.northwestern.edu 2026-11-08
  20. For start-stop or varying cycles, keep the motor nominal torque above the RMS load torque. Level: must. maxonmotor.com 2026-11-08
  21. For continuous operation at a single load point, choose a motor whose nominal torque exceeds the load torque. Level: must. maxonmotor.com 2026-11-08
  22. Allow for no-load current in nominal torque: M_N = kM (I_N - I_0). Level: should. maxonmotor.com 2026-11-08
  23. Limit peak current in a duty cycle to I_on = I_N sqrt(T / t_on), with t_on no longer than the winding thermal time constant. Level: must. maxonmotor.com 2026-11-08
  24. Expect overload times of several seconds for the smallest motors and about one minute for the largest. Level: guide. maxonmotor.com 2026-11-08
  25. Count the voltage drop in the power stage when finding the maximum voltage at the motor. Level: must. maxonmotor.com 2026-11-08
  26. Count supply voltage, voltage drops and current limit when calculating available actuator torque. Level: should. standards.nasa.gov 2026-11-08“Supply voltage, voltage drops, current limit”
  27. Use the linear speed-torque relation w = V/kt - (R/kt^2) tau for constant voltage, ignoring the inductance term. Level: guide. hades.mech.northwestern.edu 2026-11-08
  28. Keep every operating point of the cycle under the speed-torque line at the maximum voltage. Level: must. maxonmotor.com 2026-11-08
  29. Include a regulating reserve of about 20 percent for bad tolerance cases of motor, load, amplifier and supply. 20 percent Level: should. maxonmotor.com 2026-11-08
  30. Do not exceed the catalog limit speed without accepting reduced service life; for maxon EC motors the limit is based on bearing life of at least 20 000 hours. 20000 h Level: should. maxonmotor.com 2026-11-08
  31. Confirm the servo amplifier delivers both the average and the peak motor current. Level: must. maxonmotor.com 2026-11-08
  32. Check supply limits before motor selection, since battery and amplifier limits can set the available peak current. Level: must. maxonmotor.com 2026-11-08
  33. Check power supply requirements, such as maximum motor terminal voltage and current limits, during the first motor selection. Level: must. maxonmotor.com 2026-11-08
  34. Find steady winding rise above ambient as the sum of thermal resistances times Joule loss. Level: should. maxonmotor.com 2026-11-08
  35. Increase winding resistance with temperature using alpha_Cu of 0.0039 per K from 25 C. 0.0039 Level: should. maxonmotor.com 2026-11-08
  36. Include resistance rise in the heating equation with the alpha-Cu denominator term, since heat depends on temperature. Level: should. maxonmotor.com 2026-11-08
  37. Treat maximum continuous current as valid at 25 C ambient, free air, no flange cooling; re-derive it for other ambients. 25 C Level: must. maxonmotor.com 2026-11-08
  38. Re-determine housing-to-ambient resistance Rth2 in the real mounting and ambient condition. Level: must. maxonmotor.com 2026-11-08
  39. Do not assume a constant continuous current at high speed: friction and eddy losses reduce it. Level: should. maxonmotor.com 2026-11-08
  40. For NASA spaceflight mechanisms, calculate torque margin as available torque over factored resisting torques minus one; zero or more meets the requirement. Level: must. standards.nasa.gov 2026-11-08“The required reserve torque is included in the equation in the form of the safety factors, so a”
  41. The minimum available torque from an energized motor is typically understood to include magnetic losses, mechanical losses and torque ripple. Level: guide. standards.nasa.gov 2026-11-08“Tavail is the minimum available torque generated by the driving or holding component (e.g.,”
  42. Meet torque margin on both sides of gearboxes and lever arms, since reducers are not fully efficient. Level: must. standards.nasa.gov 2026-11-08“wave gear drives, lever arms) shall meet torque margin requirements at both the input and output”
  43. Keep static torque margin above zero over the full range of motion. Level: must. standards.nasa.gov 2026-11-08“[DDMR 12] Static torque margin per Equation 4-1 and Table 1 shall be greater than zero within”
  44. Treat motor catalog data as average values and allow for field strength and wire resistance tolerances. Level: should. maxonmotor.com 2026-11-08
  45. For NASA-STD-5017B EC brushless motors, measure Kt, Km, the torque-speed curve, phase resistances, phase inductances and end-to-end commutated torque, or calculate them from measured values. Use flight-representative drive electronics for the torque-speed curve. Level: should. standards.nasa.gov 2026-11-08“[DDMR 46] Each electronically commutated (EC) brushless motor shall have the”
  46. Run a duty thermal test until temperature reaches a steady trend or five thermal time constants have passed. 0.1 C/min Level: should. arxiv.org 2026-11-08“0.1◦ C/min), or (ii) five thermal time constants have elapsed (estimate τth from initial temperature”
  47. Scale torque rating with duty by the square root law: continuous torque is the 50 percent duty torque divided by 1.414, and the 25 percent duty torque is 1.414 times the 50 percent duty torque. 1.414 Level: guide. pergatory.mit.edu 2026-11-08
  48. In a Robonine STS3215 test, issues appeared at 71°C and no built-in thermal protection was apparent, so manual shutdown is needed at that temperature. A later page comment says firmware protection cuts torque near 70°C. Level: should. robonine.com 2026-11-08
  49. Doggo's motor test raised current until the winding reached a steady 125 C, a value often used as the maximum for stator windings. 125 C Level: guide. arxiv.org 2026-11-08
  50. Note the maxon Rth2 and maximum continuous current values come from tests with the motor end-mounted on a vertical plastic plate. Level: should. maxonmotor.com 2026-11-08
  51. Metal-flange motors on a good heat-conducting holder can lower Rth2 by up to 80 percent. 80 percent Level: guide. maxonmotor.com 2026-11-08
  52. Use tau = kt I for motor torque. Level: guide. hades.mech.northwestern.edu 2026-11-08
  53. For NASA-STD-5017B theory-or-analysis torque data, use minimum factors of 3.00 on variable, 1.50 on fixed, and 1.25 on acceleration torque. 3.0 Level: must. standards.nasa.gov 2026-11-08“Theory or analysis 3.00 1.50 1.25”
  54. For NASA-STD-5017B torques from development test at expected environmental extremes, qualification test, lot acceptance test at expected environmental extremes, or flight acceptance test at ambient, use minimum factors of 2.50 on variable, 1.35 on fixed and 1.15 on acceleration torque. 2.5 Level: must. standards.nasa.gov 2026-11-08“Qualification test 2.50 1.35 1.15”
  55. For flight-hardware acceptance testing at expected environmental extremes, use minimum factors of 2.00, 1.25, and 1.10. 2.0 Level: must. standards.nasa.gov 2026-11-08“Acceptance test of flight hardware at expected environmental 2.00 1.25 1.10 extremes”
  56. Combine only worst cases that can occur together, for example do not stack hot driving torque with cold resisting torque. Level: should. standards.nasa.gov 2026-11-08“Only those worst-case combinations that can occur simultaneously need to be considered.”
  57. Keep holding torque margin above zero per the same equation and table at specified positions within the mechanism's full range of motion. Level: must. standards.nasa.gov 2026-11-08“[DDMR 14] Holding torque margin per Equation 4-1 and Table 1 shall be greater than zero at the”
  58. Do not apply NASA torque margin to mechanisms that must provide a specific torque within a narrow tolerance range. Level: must. standards.nasa.gov 2026-11-08“Torque margin is not applicable to mechanisms that must provide a specific torque value within”
  59. For maxon graphite-brush and EC motors, which tend to have higher current loads, maximum rotor temperature is 125 C, in individual cases up to 155 C. 125 C Level: must. maxonmotor.com 2026-11-08
  60. Use 85 C as maximum rotor temperature for precious metal commutated maxon motors. 85 C Level: must. maxonmotor.com 2026-11-08
  61. Do not exceed maximum rotor temperature, even temporarily. Level: must. maxonmotor.com 2026-11-08
  62. A winding at 75 C has nearly 20 percent higher resistance than at 25 C. 20 percent Level: should. maxonmotor.com 2026-11-08
  63. Allow for magnet weakening of 1 to 10 percent at 75 C, depending on material. Level: should. maxonmotor.com 2026-11-08
  64. Do not exceed 125 C power MOSFET junction temperature, or 40 C below the maker's maximum, whichever is lower. 125 C Level: should. nepp.nasa.gov 2026-11-08“2/ Do not exceed Tj = 125 °C or 40 °C below the manufacturer's maximum rating, whichever is lower or less.”
  65. For microcircuits do not exceed 110 C junction or 40 C below the maker's maximum, whichever is lower. 110 C Level: should. nepp.nasa.gov 2026-11-08“2/ Do not exceed Tj = 110 °C or 40 °C below the manufacturer's maximum rating, whichever is lower.”
  66. Keep continuous touch surfaces at or below 44 C. 44 C Level: must. ntrs.nasa.gov 2026-11-08“The maximum allowable continuous touch temperature for surfaces in crewed spacecraft is 44 degrees Centigrade”
  67. Add warning labels for surfaces from 45 to 50 C and protective measures above 50 C. 50 C Level: should. ntrs.nasa.gov 2026-11-08“employed for surface temperatures between 45 and 50°C (113 and 122°F), and should have protective measures above 50°C (122°F).”Review note: Source says warning labels and protective measures above 50 C use should, not shall; must is over-strong.
  68. Demonstrate operation at temperature 10 C beyond the expected range. 10 C Level: should. standards.nasa.gov 2026-11-08“extremes 10°C beyond the range of expected flight temperatures shall be demonstrated.”
  69. Model winding and stator as separate thermal stages, because the winding heats in seconds and the stator in 1 to 30 minutes. 30 min Level: should. maxonmotor.com 2026-11-08
  70. Expect outrunner motors to trade reduced thermal dissipation and higher inertia for higher torque density. Level: guide. arxiv.org 2026-11-08
  71. Treat gear ratio as a trade-off: a higher ratio adds static torque, but reflected inertia scales with ratio squared and friction rises, which degrades torque-mode bandwidth. Level: should. arxiv.org 2026-11-08“Increasing gear ratio N raises static torque but also increases reflected inertia (∝N 2 ) and friction, which degrades torque-mode bandwidth,”
  72. Low gear ratios reduce reflected inertia but can increase Joule-heating energy for a given torque. Level: should. fab.cba.mit.edu 2026-11-08
  73. Slocum's matched-inertia doctrine sets the transmission ratio so the power to accelerate the motor equals the power to accelerate the load, for maximum acceleration. It assumes a triangular velocity profile and low friction and external forces. Level: guide. pergatory.mit.edu 2026-11-08
  74. Do not assume current maps to torque at gear ratios well above 10; backlash, vibration and friction can no longer be ignored. Level: guide. manipulation.csail.mit.edu 2026-11-08
  75. Quasi-direct drive uses a single-stage reduction with a ratio under 10:1. It raises torque at the expense of control bandwidth but keeps the motor backdrivable. Level: guide. arxiv.org 2026-11-08
  76. The Blue arm paper describes QDD actuators with transmission ratios below 1:10 as having low friction and high backdrivability. Level: guide. arxiv.org 2026-11-08