Worked example: a mobile robot, LeKiwi
Result. LeKiwi is a three-wheel base with an SO-101 pair. Every one of its 33 BOM rows is priced, and it has separate 12 V and 5 V builds.
- Rows sum to $473.77 (12 V with arm pair) and $490.15 (5 V with arm pair). The project's headline prices are $482 and $499. The rows do not explain the $8.23 and $8.85 gaps.
- Servos are 44.0 and 45.9 percent of cost: 3 on wheels and 12 in the arm pair.
- On 12 V a wheel servo can push at most 57.9 N at the rim, from the README stall of 30 kg·cm, and only for a moment. The rated force and the rim speed need the maker's rated torque and no-load speed, which this site cannot show. The 5 V build cannot be checked: the database has no servo torque or speed at 5 V.
- The battery and plug rows say "5a". Compare that with three times the stall current on your servo's sheet. This site cannot show the maker's current figures.
- The list has no fuse, breaker or stop switch. The fuse-or-breaker check is open [1].
- The database has no mass for this robot, so no load, slope or acceleration check is possible.
The arithmetic is in tools/book_calcs/mobile.py; its output is tools/book_calcs/out/mobile.md.
Parts list and cost
Source: the LeKiwi BOM.md (lekiwi). All rows are USD. The database keeps the source's blocks as configs.
| Config block | Rows | Sum (USD) | Used by |
|---|---|---|---|
| All versions | 8 | 173.15 | 12 V and 5 V builds |
| 12 V base | 5 | 100.84 | 12 V build |
| 12 V SO-101 pair | 3 | 199.78 | 12 V build with arms |
| 5 V base | 4 | 105.00 | 5 V build |
| 5 V SO-101 pair | 3 | 212.00 | 5 V build with arms |
| Wired | 10 | 183.91 | wired base, stands alone |
| Build | Arithmetic | Sum (USD) | Project price | Gap |
|---|---|---|---|---|
| 12 V with pair | 173.15 + 100.84 + 199.78 | 473.77 | 482 | 8.23 |
| 5 V with pair | 173.15 + 105.00 + 212.00 | 490.15 | 499 | 8.85 |
| 12 V base only | 173.15 + 100.84 | 273.99 | not in prices table | |
| 5 V base only | 173.15 + 105.00 | 278.15 | not in prices table | |
| Wired base | 183.91 | 183.91 | not in prices table |
Use the rows, not the headline, when you compare cost. The rows include no frame or printed parts, so neither figure is a full build cost.
| Group | 12 V with pair (USD) | Share | 5 V with pair (USD) | Share |
|---|---|---|---|---|
| Servos | 208.35 | 44.0% | 225.00 | 45.9% |
| Compute and storage (Raspberry Pi 5, microSD) | 71.23 | 15.0% | 71.23 | 14.5% |
| Power | 54.98 | 11.6% | 52.00 | 10.6% |
| Wheels, 3 at $9.99 | 29.97 | 6.3% | 29.97 | 6.1% |
| Cameras, 2 at $12.98 | 25.96 | 5.5% | 25.96 | 5.3% |
| Tools and clamps | 24.00 | 5.1% | 24.00 | 4.9% |
| Cables and connectors | 23.19 | 4.9% | 25.00 | 5.1% |
| Motor control boards, 2 | 21.10 | 4.5% | 22.00 | 4.5% |
| Fasteners | 14.99 | 3.2% | 14.99 | 3.1% |
| Total | 473.77 | 490.15 |
The two power paths
| Item | 12 V build | 5 V build |
|---|---|---|
| Base energy | "12v 5a Battery", $32.99 | 20000 mAh 85 W power bank, $42.00 |
| Base servos, 3 | 12 V STS3215 at $13.89 | 7.4 V STS3215 at $15.00 |
| Arm servos, 12 | same 12 V part | same 7.4 V part |
| Converter and cables | "12v to 5v 5a USB-C converter", $9.99 | "USB-C Cable 2pcs", $8.00 |
| Wiring | lever connector, "12v 5a DC plug connector" | "USB-C To DC Cable" |
| Arm supply | one "Power Supply", $12.00 | one "Power Supply", $10.00 |
The database gives no volts or amps for the two "Power Supply" rows, and no gear ratio for these two servo ids.
The 5 V build runs a 7.4 V class servo well below its nominal voltage. The database holds a supply range for the C001 and C044 only from the maker wiki and a seller, which this site cannot show, so check the minimum on your servo's sheet. The database holds no torque or speed row at 5 V for any STS3215. So every number below is for 6 V or 12 V. The STS3215 voltage-rating guideline's check asks every actuator fact to carry a voltage [2], and the supply-sag guideline counts supply voltage in available torque [3]. For the arm itself, including the leader and follower voltage conflict, see chapter 19.
Wheel numbers
The BOM names a 4 inch omni wheel: diameter 4 x 25.4 = 101.6 mm, radius 50.8 mm.
Rim speed = rpm x π x 0.1016 / 60 = rpm x 0.00532 m/s. This is rim speed at no load. Body speed depends on wheel angle and base radius, which are not in the database. The database holds STS3215 no-load speeds only from the maker wiki, a seller and a bench test, which this site cannot show. Put the no-load rpm at your supply voltage from your servo's sheet into the formula.
Rim force = torque / 0.0508. This site can show only the README stall torques for these servos [2]:
| Servo | Stall (N·m) | Force at stall, per wheel |
|---|---|---|
| 12 V STS3215, 30 kg·cm | 2.942 | 57.9 N |
| 7.4 V STS3215, 16.5 kg·cm at 6 V | 1.618 | 31.9 N |
Stall is a momentary maximum [4], so these forces are upper bounds, not design values. For design, use the rated torque from your servo's sheet: rated force per wheel = rated torque / 0.0508. Do not add the three wheels: on a three-wheel base they do not all push the same way. The torque-speed actuator-model guideline covers the sim side [5].
The check stops here. Without mass, wheel friction and slope, these forces cannot be turned into an acceleration or a gradeability.
Current budget
This is the one check the BOM can test against a supply. It needs each servo's no-load and stall current. The 12 V STS3215 id has no current facts. The database holds currents for the 12 V C018 only from the maker wiki, which this site cannot show. So the table gives the method, with the servo counts from the BOM. Take the currents from your servo's sheet.
| Case | Arithmetic |
|---|---|
| 3 wheel servos, no load | 3 x no-load current |
| 3 wheel servos, stall | 3 x stall current |
| 3 wheel and 6 arm servos, no load | 9 x no-load current |
| 3 wheel and 6 arm servos, stall | 9 x stall current |
The battery and plug rows say "5a" in the item name. The database has no rating fact for them, and does not say whether the follower arm shares that battery. If three times the stall current is over 5 A, a base jammed at full command goes past that rating. Expect a current limit or a voltage sag there [6], [7], [3].
Protection
| Robot | Fuse or breaker row | Stop or switch row |
|---|---|---|
| LeKiwi | none | none |
| XLeRobot | none | none |
| Open Source Rover | "fuse holder", "Fuse" | "estop switches", "external switch" |
The rover's list shows the rows to add. The power-protection guideline asks for a fuse or breaker on every power wire, close to the source [1]. For an SO-101 bench setup, the stop-readiness guideline says to be ready to stop with CTRL+C or by unplugging power before running a policy [8]. A mobile base cannot be reached as quickly as a bench arm.
Two other mobile lists
| Item | LeKiwi, 12 V with pair | XLeRobot | Open Source Rover |
|---|---|---|---|
| BOM rows | 16 of 33 used | 17 | 109 |
| Priced rows | 16 | 17 | 29 per piece, 31 per pack, 49 unpriced |
| Sum of rows | $473.77 | $679.16 ($651.18 without tools) | $1,250.62 |
| Project price in the database | $482 | about $660, basic; $579 assembly kit | none |
| Drive actuators | 3 servos | 3 servos | 6 goBILDA 5203 gearmotors at $42.99, plus 4 servos at $31.99 |
| Servo cost | $208.35 (44.0%) | $216.00, 15 at $14 and $16 (31.8%) | $385.90 for the 10 drive units above |
| Wheel | 101.6 mm omni, $9.99 | same wheel | 144 mm, $24.99 |
| Rim speed | not shown: needs the servo's no-load speed | same servo | 1.68 m/s (223 RPM from the item name, x π x 0.144 / 60) |
| Battery | "12v 5a Battery", $32.99 | Anker SOLIX C300, $179.99 (26.5%) | no battery row |
| Chassis | no row | IKEA RASKOG cart, $39.99 | goBILDA rows |
Reading the three lists:
- XLeRobot and LeKiwi share the servo family and the wheel. XLeRobot spends the difference on energy and a chassis you can buy.
- The rover's sum counts pack rows at
ceil(qty / pack). Its control board block has 49 unpriced rows, including 3 RoboClaw drivers and a Raspberry Pi 4B. So $1,250.62 is mechanics and drive only. - The rover is the only one of the three with a list of protection parts.
What the database cannot tell you here
- Robot mass for LeKiwi or the rover. XLeRobot has a 12 kg claim.
- Base radius, wheel angle or wheel friction for any of the three.
- Torque or speed of any STS3215 at 5 V.
- Rating of the "12v 5a" battery, or either "Power Supply".
- Facts for the 7.4 V id used in this BOM, and any fact for the 12 V id beyond its README stall torque. The BOM rows give prices only.
- Runtime for LeKiwi. Neither of its energy stores has a rated capacity fact. XLeRobot claims 8 hours in intensive use and 12 hours or more in normal use, and the rover claims at least 3 hours.
Guidelines this example exercises
| Guideline | Result here |
|---|---|
| A servo's stall torque is its maximum momentary output and differs from its continuous rating. Real-world output is generally closer to the performance-graph measurements. [4] | Stall force per wheel computed from the README stall. The rated force needs the servo's sheet. No load to compare it with. |
| The STS3215 7.4 V version is rated at 16.5 kg·cm stall torque at 6 V; the 12 V version is rated at 30 kg·cm [2]; Count supply voltage, voltage drops and current limit when calculating available actuator torque. [3] | 5 V build has no value at its own voltage. |
| Check supply limits before motor selection, since battery and amplifier limits can set the available peak current [6]; A multi-cell battery must provide the required capacity and current within the application's voltage limits. [7] | Open: the stall current needs the servo's sheet, and the "5a" rating is not confirmed. |
| Protect every power wire with a fuse or breaker located as close as possible to the source bus. [1] | Open: no fuse or breaker row on LeKiwi or XLeRobot. |
| On an SO-101 bench setup, be ready to stop with CTRL+C or by unplugging power before running a policy. [8] | Written for an SO-101 bench setup. The pair on this base is not one. |
| Use DCMotor when the actuator model needs a four-quadrant torque-speed envelope rather than a fixed effort clip. [5] | Rim speed is no-load; a fixed torque clip omits the speed loss. |
Category pages: Servos, Battery packs, Motor drivers.
Sources
Each guideline in this chapter with its source, the date it was read and the exact words of the source. Level: must means breaking it causes failure or harm, should is good practice, guide is a rule of thumb.
- Protect every power wire with a fuse or breaker located as close as possible to the source bus. Level: must. raanz.org.nz 2026-11-08“with circuit breakers or fuses located as close”
- The STS3215 7.4 V version is rated at 16.5 kg·cm stall torque at 6 V; the 12 V version is rated at 30 kg·cm. Level: guide. github.com 2026-11-08“The 12V version has a stall torque of 30kg.cm.”
- Count supply voltage, voltage drops and current limit when calculating available actuator torque. Level: should. standards.nasa.gov 2026-11-08“Supply voltage, voltage drops, current limit”
- A servo's stall torque is its maximum momentary output and differs from its continuous rating. Real-world output is generally closer to the performance-graph measurements. Level: guide. emanual.robotis.com 2026-11-08
- Use DCMotor when the actuator model needs a four-quadrant torque-speed envelope rather than a fixed effort clip. Level: guide. isaac-sim.github.io 2026-11-08“Same PD torque, clipped to a four-quadrant torque-speed envelope.”
- Check supply limits before motor selection, since battery and amplifier limits can set the available peak current. Level: must. maxonmotor.com 2026-11-08
- A multi-cell battery must provide the required capacity and current within the application's voltage limits. Level: must. ntrs.nasa.gov 2026-11-08“adequate thermal management. The battery must provide both the capacity and current required”
- On an SO-101 bench setup, be ready to stop with CTRL+C or by unplugging power before running a policy. Level: must. docs.nvidia.com 2026-11-08