Kinematics and workspace
Do these five things before you size a joint.
- Count mobility with the mobility formula and check it against design intent [1].
- Workspace is the part of task space within reach of the end-effector frame [2]. Sample it with real joint limits. Do not draw a sphere of arm length.
- Sweep the Jacobian rank across the workspace and flag each drop [3].
- Compute joint torque from wrench and gravity at every pose [4], [5]. This feeds chapter 4.
- Set stops, stroke margin and clearances [6], [7], [8].
Most guidelines here come from open-chain robot texts. Those from the NASA mechanisms standard were written for spaceflight mechanisms, not ground robots. Each guideline states its scope.
Degrees of freedom
Count first. dof = m(N-1-J) + sum(f_i), with m of 3 in the plane and 6 in space [1]. Dependent joint constraints make this only a lower bound, which matters for closed chains.
The count sets what the tool can do. SCARA has four and cannot tilt the tool, which fits flat assembly. Five-axis low-cost arms lose a direction too [9]. A seventh axis adds redundancy, but only if joints exceed task dimensions [10].
| Level | Statement | Check | Source |
|---|---|---|---|
| should | Count mobility with dof = m(N-1-J) + sum(f_i); m is 3 in the plane and 6 in space. Dependent joint constraints make this only a lower bound. | model-lint: computed dof equals design intent | [1] |
| should | Call a chain redundant only if it has more joints than task space dimensions, and plan inverse kinematics with the pseudoinverse. | calc: n_joints > task_dim; IK method chosen | [10] |
| should | A manipulator with under six degrees of freedom cannot move in every spatial direction; a singular configuration lowers its end-effector freedom further. | calc: rank(J) vs required task twist | [9] |
| should | At high gear ratio the mass matrix becomes more diagonal, so joint dynamics decouple; do not assume this at low ratio. | calc: off-diagonal terms of M(q) vs diagonal, including rotors | [11] |
| should | A control model is underactuated at a state and time when its actuation matrix rank is below configuration dimension; input constraints can also cause underactuation. | model-lint: rank(f2) >= dim(q), or a plan for underactuated control | [12] |
Workspace and inverse kinematics
Reach on a data sheet is one number. Workspace is a set of poses. An arm that lists a reach, such as PAROL6 at 408 mm, may not reach that point at every tool orientation. A tool offset changes the result [13].
Robot pages list joint ranges and link masses where a model file gives them. Sample with those values, then repeat with your real tool.
An IK solver should return a fail state, not a wrong pose [14]. Many common six-dof open-chain arms have a closed-form analytic IK solution [15]. If you need that, choose the geometry and the IK method together.
| Level | Statement | Check | Source |
|---|---|---|---|
| should | Workspace is the part of task space within reach of the end-effector frame. | sim: sample reachable poses with joint limits | [2] |
| should | A spherical wrist makes dextrous equal to reachable workspace only if the end-effector frame is at wrist centre; an offset complicates this. | sim: dextrous workspace sampled with the real tool offset | [13] |
| should | Handle inverse kinematics with multiple or no solutions. | sim: IK solver returns a fail state for out-of-reach poses | [14] |
| guide | Many common six-dof open-chain arms have a closed-form analytic inverse kinematics solution. | review: IK method and geometry chosen together | [15] |
Singularities
A singularity is any configuration where the Jacobian rank is not maximal. Near one, joint speeds for a given tool speed in certain directions can become extremely large [16]. Moving the frames does not remove it [17]. It also lets the robot resist arbitrary wrenches in the direction of the lost mobility [18].
These five axis patterns apply to six-dof spatial open chains with revolute and prismatic joints. They can be linted from the model, without simulation. Treat them as the first model checks for a kinematic design.
| Level | Statement | Check | Source |
|---|---|---|---|
| should | For six-dof spatial open chains with revolute and prismatic joints, flag two collinear revolute joint axes as singular. | model-lint: no two revolute axes collinear within the task workspace | [19] |
| should | For six-dof spatial open chains with revolute and prismatic joints, flag three coplanar, parallel revolute axes as singular. | model-lint: check coplanar parallel triples across configurations | [20] |
| should | For six-dof spatial open chains with revolute and prismatic joints, flag four revolute axes intersecting at a common point as singular. | model-lint: check four-axis intersections | [21] |
| should | For six-dof spatial open chains with revolute and prismatic joints, flag four coplanar revolute joints as singular. | model-lint: check four coplanar axes | [22] |
| should | For six-dof spatial open chains with revolute and prismatic joints, flag six revolute axes intersecting a common line as singular. | model-lint: check six axes meeting one line | [23] |
The other singularity guidelines need a sweep or a calculation.
| Level | Statement | Check | Source |
|---|---|---|---|
| should | Define a singularity as any configuration where the Jacobian rank is not maximal; analyse it across the workspace. | sim: sweep configurations and flag rank drop of J | [3] |
| should | Near singular configurations, joint velocities required for a desired end-effector velocity in certain directions can be extremely large. | sim: joint speed along planned paths <= limits | [16] |
| should | Treat singularity results as independent of fixed and end-effector frame choice; a change of frame will not remove one. | review: singularity analysis does not depend on the choice of frame | [17] |
| should | A singularity loses mobility while enabling the robot to resist arbitrary wrenches in the direction of that lost mobility. | calc: joint torque from J^T F near singular poses | [18] |
| should | Check closed-chain actuator singularities with the constraint Jacobian rank. | calc: rank(H_p) in closed-chain workspace | [24] |
Manipulability
Use a measure to compare designs and poses. Plot it across the workspace and mark the low regions. Note the directions: isotropy mu1 and condition number mu2 are better when small, and volume mu3 is better when large. Force ability runs opposite to velocity ability [25], so a pose good for speed is weak for force in that direction.
| Level | Statement | Check | Source |
|---|---|---|---|
| should | Use mu1 = sqrt(lmax / lmin) of J J^T as an isotropy measure: values near 1 are preferred and it tends to infinity at singularity. | sim: mu1 across workspace; flag high values | [26] |
| should | Use mu2 = lmax / lmin, the square of mu1, as the condition number of J J^T; smaller is better, 1 is ideal. | sim: mu2 across workspace | [27] |
| should | Use mu3 = sqrt(det(J J^T)), proportional to manipulability ellipsoid volume; here a larger value is better. | sim: mu3 across workspace | [28] |
| should | Take manipulability ellipsoid axes from eigenvectors of J J^T, with semi-axis lengths equal to square roots of eigenvalues. | sim: plot ellipsoid at key poses | [29] |
| should | Take force ellipsoid axes from eigenvectors of (J J^T)^-1; force ability is opposite to velocity ability. | sim: force ellipsoid at key poses | [25] |
Statics and gravity
tau = J^T F, with J and F in the same frame [4]. Gravity goes into the budget through tau = M ddq + c + g [5]. Run both at every reachable pose and payload.
At high gear ratio the mass matrix becomes more diagonal and joint dynamics decouple. Do not assume this at low ratio [11]. This matters for QDD joints.
| Level | Statement | Check | Source |
|---|---|---|---|
| should | Find joint torques from wrench with tau = J^T F, using the same frame for J and F. | calc: tau = J^T(q) * F at all reachable static poses and payloads | [4] |
| should | Include gravity in the joint torque budget from the equations of motion, tau = M ddq + c + g. | sim: g(q) torque over the workspace | [5] |
Closed chains
Parallel and delta layouts are closed chains. They can have multiple forward kinematics solutions, so track the assembly mode [30]. Check actuator singularities with the constraint Jacobian rank [24]. The parallel class notes singularities inside the workspace as a main cost.
Travel, stops and clearance
NASA gives no single stroke margin, since the right margin depends on the mechanism [7]. You still must set one. A limit switch must not impede travel [31]. Stops must not jam, and they must survive impact at full speed [6], [32]. Keep position commands inside joint ranges [33].
| Level | Statement | Check | Source |
|---|---|---|---|
| must | Establish static and dynamic clearances between mechanism parts and other structure, and keep them through service life. | sim: swept volume clearance across workspace at max deflection | [8] |
| should | Measure clearances on the highest level of assembly possible. | measure: clearance gauges on the assembled robot | [34] |
| must | Set stroke margin requirements for all mechanisms; NASA gives no single number since appropriate margin depends on the mechanism. | calc: required travel + uncertainty <= hard stop travel | [7] |
| must | Mount limit switches so they cannot physically impede mechanism travel; worst-case travel must not damage them. | sim: switch actuator clearance across full travel | [31] |
| should | Provide direct indication of critical mechanism states. | review: critical joint states measured directly, for example output encoder | [35] |
The database has no numeric limits for condition number, manipulability or stroke margin. These guidelines define the measure and leave the limit to you. Set the limit from your task, and record it.
Sources
Each guideline in this chapter with its source, the date it was read and the exact words of the source. Level: must means breaking it causes failure or harm, should is good practice, guide is a rule of thumb.
- Count mobility with dof = m(N-1-J) + sum(f_i); m is 3 in the plane and 6 in space. Dependent joint constraints make this only a lower bound. 6 Level: should. hades.mech.northwestern.edu 2026-11-08
- Workspace is the subset of task space that the end-effector frame can reach. Level: should. hades.mech.northwestern.edu 2026-11-08
- Define a singularity as any configuration where the Jacobian rank is not maximal; analyse it across the workspace. Level: should. hades.mech.northwestern.edu 2026-11-08
- Find joint torques from wrench with tau = J^T F, using the same frame for J and F. Level: should. hades.mech.northwestern.edu 2026-11-08
- Include gravity in the joint torque budget from the equations of motion, tau = M ddq + c + g. Level: should. hades.mech.northwestern.edu 2026-11-08
- Fit non-jamming mechanical stops wherever overtravel harms the mechanism or system. Level: must. standards.nasa.gov 2026-11-08“[DDMR 30] Non-jamming mechanical stops shall be incorporated into all mechanisms where”
- Set stroke margin requirements for all mechanisms; NASA gives no single number since appropriate margin depends on the mechanism. Level: must. standards.nasa.gov 2026-11-08“[DDMR 18] Stroke margin requirements shall be established for all mechanisms.”
- Establish static and dynamic clearances between mechanism parts and other structure, and keep them through service life. Level: must. standards.nasa.gov 2026-11-08“[DDMR 3] Static and dynamic clearance requirements between mechanism components and any other”
- A manipulator with under six degrees of freedom cannot move in every spatial direction; a singular configuration lowers its end-effector freedom further. Level: should. cds.caltech.edu 2026-11-08
- Call a chain redundant only if it has more joints than task space dimensions, and plan inverse kinematics with the pseudoinverse. Level: should. hades.mech.northwestern.edu 2026-11-08
- At high gear ratio the mass matrix becomes more diagonal, so joint dynamics decouple; do not assume this at low ratio. Level: should. hades.mech.northwestern.edu 2026-11-08
- A control model is underactuated at a state and time when its actuation matrix rank is below configuration dimension; input constraints can also cause underactuation. Level: should. underactuated.csail.mit.edu 2026-11-08
- A spherical wrist makes dextrous equal to reachable workspace only if the end-effector frame is at wrist centre; an offset complicates this. Level: should. cds.caltech.edu 2026-11-08
- Handle inverse kinematics with multiple or no solutions. Level: should. hades.mech.northwestern.edu 2026-11-08
- A popular class of six-dof open-chain structures has closed-form analytic inverse kinematics. Level: guide. hades.mech.northwestern.edu 2026-11-08
- Near singular configurations, joint velocities required for a desired end-effector velocity in certain directions can be extremely large. Level: should. cds.caltech.edu 2026-11-08
- Treat singularity results as independent of fixed and end-effector frame choice; a change of frame will not remove one. Level: should. hades.mech.northwestern.edu 2026-11-08
- A singularity loses mobility while enabling the robot to resist arbitrary wrenches in the direction of that lost mobility. Level: should. hades.mech.northwestern.edu 2026-11-08
- For six-dof spatial open chains with revolute and prismatic joints, flag two collinear revolute joint axes as singular. Level: should. hades.mech.northwestern.edu 2026-11-08
- For six-dof spatial open chains with revolute and prismatic joints, flag three coplanar, parallel revolute axes as singular. Level: should. hades.mech.northwestern.edu 2026-11-08
- For six-dof spatial open chains with revolute and prismatic joints, flag four revolute axes intersecting at a common point as singular. Level: should. hades.mech.northwestern.edu 2026-11-08
- For six-dof spatial open chains with revolute and prismatic joints, flag four coplanar revolute joints as singular. Level: should. hades.mech.northwestern.edu 2026-11-08
- For six-dof spatial open chains with revolute and prismatic joints, flag six revolute axes intersecting a common line as singular. Level: should. hades.mech.northwestern.edu 2026-11-08
- Check closed-chain actuator singularities with the constraint Jacobian rank. Level: should. hades.mech.northwestern.edu 2026-11-08
- Take force ellipsoid axes from eigenvectors of (J J^T)^-1; force ability is opposite to velocity ability. Level: should. hades.mech.northwestern.edu 2026-11-08
- Use mu1 = sqrt(lmax / lmin) of J J^T as an isotropy measure: values near 1 are preferred and it tends to infinity at singularity. Level: should. hades.mech.northwestern.edu 2026-11-08
- Use mu2 = lmax / lmin, the square of mu1, as the condition number of J J^T; smaller is better, 1 is ideal. 1 Level: should. hades.mech.northwestern.edu 2026-11-08
- Use mu3 = sqrt(det(J J^T)), proportional to manipulability ellipsoid volume; here a larger value is better. Level: should. hades.mech.northwestern.edu 2026-11-08
- Take manipulability ellipsoid axes from eigenvectors of J J^T, with semi-axis lengths equal to square roots of eigenvalues. Level: should. hades.mech.northwestern.edu 2026-11-08
- Expect closed chains to have multiple forward kinematics solutions. Level: should. hades.mech.northwestern.edu 2026-11-08
- Mount limit switches so they cannot physically impede mechanism travel; worst-case travel must not damage them. Level: must. standards.nasa.gov 2026-11-08“[DDMR 61] Switch mounting, orientation, and actuation shall be such that the switch cannot”
- Keep positive margin with full design factors under worst-case transient loads from stop impact. Level: must. standards.nasa.gov 2026-11-08“factors of safety applied when subjected to worst-case transient loads from mechanical stop impact.”
- Keep position command ranges inside joint ranges, except for a gripper that must close past pad contact. Level: must. mujoco.readthedocs.io 2026-11-08
- Measure clearances on the highest level of assembly possible. Level: should. standards.nasa.gov 2026-11-08“[DDMR 8] Clearance measurements shall be performed on the highest level of assembly possible.”
- Provide direct indication of critical mechanism states. Level: should. standards.nasa.gov 2026-11-08“[DDMR 26] A direct indication of the critical states of each mechanism shall be provided.”