Choosing a robot type
Do this before you choose any part.
- Write the task: what is carried, how far, over what ground, and whether a person is near.
- Choose the class whose limits you can accept. Each class below states its costs.
- Find a catalogued robot close to your numbers. If nothing is close, ask why before you design one.
- Read its joint count against the degrees-of-freedom guideline [1]: under six degrees of freedom, the tool cannot move in every spatial direction.
Classes at a glance
Classes come from the catalog. Browse the models on Robots.
| Group | Class | Layout | Choose it when | Main cost | Example |
|---|---|---|---|---|---|
| Arm | Serial articulated | Chain of rigid links and motor-driven joints | You need wide reach and tool orientation from one base | Joint errors add along the chain; singularities near some poses | UR12e |
| Arm | Cobot | Light arm with limits on force and speed | It works near people, after a risk assessment | Speed and force limits cut throughput; safety rests on the whole cell | FR3 |
| Arm | Desktop leader-follower | Hobby servo arms for teleoperation data | You collect imitation-learning data on a budget | Low-cost servos limit accuracy and torque; build quality varies | SO-ARM101 |
| Arm | Dual-arm | Two arms on one frame | The task needs two hands | Doubles cost, calibration and collision checks | ALOHA |
| Arm | SCARA | Two parallel vertical rotary joints plus a vertical slide | Flat assembly, pin insertion, pick and place | No tool tilt | MG400 |
| Arm | Cartesian or gantry | Three linear axes at right angles | Straight-line moves over a large volume | Large frame for the reach; no tool orientation without a wrist | none in Robots |
| Arm | Delta | Three arms to a small platform, motors in the base | Very fast picking of light parts | Small working volume | none in Robots |
| Arm | Parallel (Stewart) | Several short chains to one platform | Stiff, accurate positioning | Limited workspace; singularities inside it | none in Robots |
| Legged | Humanoid | Torso, head, two arms, two legs | The space and tools are made for people | Balance, falls, short runtime, cost | G1 |
| Legged | Quadruped | Four walking legs | Stairs and rough ground, carrying sensors | Mechanical complexity; slow on flat floors | Go2 |
| Mobile | Wheeled or tracked base | Differential, omnidirectional or tracked | Flat floors, lowest energy per metre | No stairs or gaps | SCOUT MINI |
| Mobile | Mobile manipulator | Arm on a mobile platform | A small arm must serve a large area | Base and arm motion couple; tip-over limits payload | Stretch 4 |
| End-effector | Gripper | Jaws, suction, magnets, adhesive | Known parts, fast cycle | Limited part range; little in-hand motion | Hand-E |
| End-effector | Dexterous hand | Multi-finger hand, tendon or direct drive | In-hand manipulation, human tools | Heavy; many failure points; calibration work | Shadow Hand |
| Aerial | Unmanned aerial vehicle | Multirotor, fixed wing, rotorcraft | Fast access over any terrain | Short flight time; little payload; airspace rules | Skydio X2 |
| Wearable | Exoskeleton | Rigid, soft or passive, worn on the body | Assist an existing body part | Fit and safety; battery mass; medical regulation | Ekso EVO |
Arms
Values are maker specs unless marked. A value marked (claim) is a maker or project claim, and (measured) is the maker's own measured result. The Universal Robots rows come from the model table in the Wikipedia article on the maker. Prices are single-unit rows from the robot page.
| Model | Class | Joints | Payload | Reach | Mass | Repeatability | Price |
|---|---|---|---|---|---|---|---|
| SO-ARM101 pair | Desktop | not listed | 150 g (claim) | 441 mm (claim) | not listed | not listed | not shown |
| SO-ARM102 | Desktop | 5 (claim) | 300 g (claim) | 483 mm (claim) | not listed | 0.1 mm (measured) | not listed |
| Koch v1.1 | Desktop | not listed | not listed | not listed | not listed | not listed | $278 parts for one follower |
| WidowX AI | Desktop | 6 | 1.5 kg | 769 mm | 4 kg | not shown | not shown |
| PAROL6 | Serial | 6 (claim) | 0.5 to 1 kg (claim) | 408 mm (claim) | 5.5 kg (claim) | 0.1 mm (claim) | not listed |
| Z1 | Serial | not listed | 2 to 3 kg | 740 mm | 4.3 to 4.5 kg | 0.1 mm | not shown |
| FR3 | Research cobot | 7 | 3 kg | 855 mm | not listed | 0.1 mm | not listed |
| UR3e | Cobot | not listed | 3 kg | 500 mm | 11.2 kg | not shown | not listed |
| UR5e | Cobot | not shown | 5 kg | 850 mm | 20.6 kg | not shown | not listed |
| UR10e | Cobot | not shown | 12.5 kg | 1300 mm | 33.5 kg | not shown | not listed |
| UR16e | Cobot | not shown | 16 kg | 900 mm | 33.1 kg | not shown | not listed |
| UR20 | Cobot | not listed | 20 kg | 1750 mm | 64 kg | not listed | not listed |
| UR30 | Cobot | not listed | 30 kg | 1300 mm | 64 kg | not listed | not listed |
Read these rows as trade-offs. UR20 and UR30 both weigh 64 kg: one gives 1750 mm reach at 20 kg, the other 1300 mm at 30 kg. UR10e and UR16e both weigh about 33 kg: one gives 1300 mm at 12.5 kg, the other 900 mm at 16 kg. Payload falls as reach grows. Low-cost arms seldom state repeatability, and the figures that exist differ in kind. SO-ARM102 gives 0.1 mm from the maker's own measurement, PAROL6 claims 0.1 mm, and FR3 states 0.1 mm as a spec. The same number can rest on very different tests. Quote repeatability with its test method, as the guideline on accuracy figures asks [2]. That guideline gives ISO 9283:1998 by its title only. The standard sets how to state and test the accuracy and repeatability of an industrial robot.
A seventh axis lets the elbow move without moving the tool, as on FR3. It makes the chain redundant, so plan inverse kinematics for it [3].
The robot table holds no gantry, delta or Stewart model in this edition. Those classes rest on class notes only. Size them from the guidelines in chapters 3 and 4.
Legged robots
Values marked (c) are claims from the Wikipedia article on Valkyrie. Others are maker specs.
| Model | Class | Joints | Height | Mass | Payload | Runtime | Price |
|---|---|---|---|---|---|---|---|
| Valkyrie | Humanoid | 44 (c) | 1.87 m (c) | 129 kg (c) | not listed | about 1 hour (c) | not listed |
| H2 | Humanoid | 31 | 1820 mm | 70 kg | not listed | not listed | $29,900 |
| G1 | Humanoid | 23 | 1320 mm | 35 kg | about 2 kg per arm | not listed | from $13,500 |
| R1 | Humanoid | 26 | 1230 mm | 29 kg | not listed | not listed | $5,900 |
| TALOS | Humanoid | not listed | 175 cm | 95 kg | 6 kg per arm | 1.5 h walking | not listed |
| Go2 | Quadruped | not listed | not listed | 15 kg | about 7 kg | not listed | from $1,600 |
| As2 | Quadruped | 12 | not listed | 20 kg | 65 kg standing, 15 kg walking | 4 h unloaded, 2.5 h loaded | not shown |
| B2 | Quadruped | not listed | not listed | 60 kg | 120 kg standing, 40 kg walking | 4 to 6 h | not shown |
| A2 | Quadruped | 12 | not listed | 42 kg | not listed | not listed | not shown |
Do not compare payload numbers across rows without reading the condition. B2 lists 120 kg standing but 40 kg walking. As2 lists 65 kg standing but 15 kg walking. Only the walking figure says what the robot carries as it moves. A load also costs runtime: As2 lists 4 h unloaded and 2.5 h loaded. The H1 has no price this site can show. Ask the maker.
A quasi-direct drive, a single stage under 10:1, keeps the motor backdrivable [4]. A low ratio can raise Joule heating for a given torque [5]. Size the joints from chapter 4, and read QDD actuators next.
Mobile robots
| Model | Class | Payload | Mass | Runtime | Other | Price |
|---|---|---|---|---|---|---|
| TIAGo Pro | Mobile manipulator | 3 kg per arm | not listed | not listed | Two 7-DoF arms, vertical reach 92 cm | not listed |
| TIAGo | Mobile manipulator | 3 kg | not listed | 4-5h, or 8-10h with 2 batteries | Height 110-145 cm | not listed |
| LeKiwi | Mobile manipulator | not listed | not listed | not listed | Self-sourced parts, 12 V version | $482 |
| XLeRobot | Mobile manipulator | 600 to 1000 g per arm (claim) | 12 kg (claim) | 8 to 12 hours (claim) | Self-sourced parts, basic version | about $660 |
| Open Source Rover | Wheeled rover | not listed | not listed | at least 3 hours on rough terrain (claim) | 7.2 Ah battery (claim) | not listed |
The battery serves both drive and arm on a mobile manipulator. Size it for both (chapter 10, [6]).
End-effectors
The gripper and hand category pages describe each class. All values are maker specs unless marked (claim). The Shadow row comes from the Wikipedia article on the hand.
| Gripper | Class | Stroke | Grip force | Payload | Mass | Closing time |
|---|---|---|---|---|---|---|
| Dex1-1 | Parallel electric | 90 mm | 5 to 120 N | 20 kg, form-fitting grasp | 550 g | 0.24 s |
| Robotiq Hand-E | Parallel electric | 50 or 100 mm | not listed | 7 kg, silicone-covered fingertips | not listed | not listed |
Read the payload condition. The class note says payload is quoted for friction grip, not form fit. Dex1-1 lists its 20 kg for a form-fitting grasp, and Robotiq Hand-E lists its 7 kg for silicone-covered fingertips. A linkage gripper wraps round parts but gives up position accuracy. A rotary gripper saves a separate joint, at the cost of a short stroke.
| Hand | Class | Joints or DoF | Mass | Payload | Price or build cost |
|---|---|---|---|---|---|
| Shadow Dexterous Hand | Tendon driven | 20 motors, 24 joints (claim) | not shown | not listed | not listed |
| ORCA v2.1 base | Tendon driven | 17 DoF | not listed | not listed | $3,500 |
| Dex3-1 | Direct drive | 7 joints | 710 g | 500 g | not shown |
| Dex5-S | Direct drive | 22 DoF | 620 g | 1 kg | not shown |
Tendon hands keep the fingers light, at the cost of tendon wear and less certain joint angles. In-finger actuators read joint state directly, and carry mass at the fingers. Hand mass sits at the end of the arm. Count it in the joint budget [7].
Aerial and wearable
The catalog holds aerial models such as Skydio X2, Crazyflie 2 and Ingenuity. The database gives Crazyflie 2.0 27 g, 7 minutes and 15 g payload, and Ingenuity 1.8 kg and 90 s. It also holds a mass and a flight time for Skydio X2, but they are not shown, because their source does not allow copying. The database has no thrust number for any of the three.
The robot table holds one exoskeleton, Ekso EVO. Its mass, assistance force and spring life are not shown, because their source does not allow copying. The class notes name the variations and the costs. One product gives no range to size a design with.
Sources
Each guideline in this chapter with its source, the date it was read and the exact words of the source. Level: must means breaking it causes failure or harm, should is good practice, guide is a rule of thumb.
- A manipulator with under six degrees of freedom cannot move in every spatial direction; a singular configuration lowers its end-effector freedom further. Level: should. cds.caltech.edu 2026-11-08
- This guideline is held back: its source does not allow us to publish it yet.
- Call a chain redundant only if it has more joints than task space dimensions, and plan inverse kinematics with the pseudoinverse. Level: should. hades.mech.northwestern.edu 2026-11-08
- Quasi-direct drive uses a single-stage reduction with a ratio under 10:1. It raises torque at the expense of control bandwidth but keeps the motor backdrivable. Level: guide. arxiv.org 2026-11-08
- Low gear ratios reduce reflected inertia but can increase Joule-heating energy for a given torque. Level: should. fab.cba.mit.edu 2026-11-08
- A multi-cell battery must provide the required capacity and current within the application's voltage limits. Level: must. ntrs.nasa.gov 2026-11-08“adequate thermal management. The battery must provide both the capacity and current required”
- Include gravity in the joint torque budget from the equations of motion, tau = M ddq + c + g. Level: should. hades.mech.northwestern.edu 2026-11-08