95 parts with data · 34 more listed by name. Columns, units and filters follow this category's display rules. Rows run from small to large. Each cell links through the part page to its source. m marks an independent measurement. How it works
Aluminium extrusion (T-slot profile, tube, angle): Hot-extruded aluminium, usually 6063-T6 or 6061-T6, cut to length. T-slot profile gives a modular robot frame, gantry or test rig you can reconfigure with slot nuts. 6063 is softer with a better finish; 6061 is stronger.
Variations: 6063-T6 (architectural, softer); 6061-T6 (structural, stronger); T-slot 2020/3030/4040 profiles, tube, angle, flat bar For: cheap, light, stiff for the cost; modular and adjustable; easy cutting and tapping Against: slot nuts slip or loosen under shock; lower stiffness than machined plate at joints; tolerances looser than CNC; 6063 is weaker than 6061 Sources: 1, 2
Aluminium alloys (6061, 6063, 6082, 5052, 5083, 2024, 7075): The default robot structure metal: about one third the density of steel. 6061-T6 is the all-rounder; 7075-T6 is much stronger but costs more and corrodes and welds worse; 5052 bends well in sheet; 5083 is for marine welded plate; 2014/2024 are aerospace Cu alloys.
Variations: 6xxx Mg-Si: 6061, 6063, 6082 (weldable, anodise well); 5xxx Al-Mg: 5052, 5083 (sheet, welding, corrosion); 7xxx Al-Zn: 7075 (highest strength); 2xxx Al-Cu: 2024, 2014A (fatigue, poor corrosion) For: low density near 2.7 to 2.8 g/cm3; easy to machine; good thermal conductivity for motor and driver heat paths; anodising for wear and colour Against: lower stiffness than steel (about 70 GPa); 7075 and 2024 not weldable in practice; galling on threads without inserts Sources: 1, 2, 3
Steels and stainless steels (mild, 4130, 304, 316, 17-4): Higher modulus (about 200 GPa) and strength than aluminium at about 2.9 times the density. Right for shafts, pins, gear blanks, fasteners and load-bearing joints; 304 and 316 for corrosion; alloy steels like 4130 for welded chromoly frames.
Variations: mild / low-carbon (cheap, weldable); alloy steels (4130 chromoly, 4140); austenitic stainless (304, 316); precipitation-hardening stainless (17-4PH) For: stiff and strong; good fatigue and wear behaviour; hard surfaces for bearing seats; cheap fasteners Against: heavy (304: 7,900 kg/m3); hard to machine in stainless; carbon steel rusts; 304 cannot be heat treated, only cold worked Sources: 1, 2
Titanium alloys (grade 5 Ti-6Al-4V): High strength (grade 5 yield 880 MPa or more) at about 57 percent of steel density, with excellent corrosion resistance. For weight-critical, high-load joints; costly and slow to machine, so use it where aluminium and steel both fail.
Variations: grade 5 (Ti-6Al-4V); grade 2 (commercially pure, formable); DMLS-printed Ti-6Al-4V For: very high specific strength; corrosion proof; biocompatible Against: low thermal conductivity (6.7 to 7.5 W/m·K) makes machining hot; high raw cost; galling with itself Sources: 1
Magnesium alloys (AZ31B and casting alloys): Lightest structural metal, density about 1.8 g/cm3. For hand-held or wearable robot housings and arms where each gram counts; machines easily but needs coating, careful chip handling and fire care.
Variations: wrought AZ31B sheet and plate; die-cast AZ91 and similar; rare-earth WE43 high-temperature For: lowest density of the structural metals; fast machining; good strength to weight Against: poor corrosion without coating; low modulus (about 42 GPa); burns in air once ignited, so chips need care; poor creep when hot Sources: 1
Machined engineering plastics (POM/acetal, PEEK, PC, PPS, UHMW, nylon): Plastic stock cut by CNC or laser. POM for gears, bushings and clips; UHMW for sliding wear pads; PEEK and PPS for hot, chemical or low-outgassing parts; PC for clear tough covers. Much lower modulus than metals, so oversize sections.
Variations: POM-C / POM-H (acetal, Delrin class); PA6 / PA66 (nylon, swells with moisture); PEEK and PPS (high temperature); PE-UHMW (lowest friction); PC (impact, clear) For: low friction and quiet gears; light; electrical insulation; self-lubricating options Against: modulus 0.7 to 4.5 GPa, far below metals; creep under constant load; thermal expansion; some (PC) stress-crack with oils Sources: 1
PCB fabrication (JLCPCB, PCBWay): Etched copper boards ordered online. For robot motor drivers, sensor boards and power distribution. Standard service gives 4 mil track and space; vias 0.15 mm; check the board files against the vendor's limits.
Variations: rigid FR-4 1 to 32 layers; aluminium-core for LED and power; flex and rigid-flex; HDI with 3 mil lines For: cheap prototypes in days; tight standard tolerances; assembly service available Against: limits differ by vendor and copper weight; heavy copper widens min track; hole and board tolerances matter for connectors Sources: 1